Registration Dossier
Registration Dossier
Data platform availability banner - registered substances factsheets
Please be aware that this old REACH registration data factsheet is no longer maintained; it remains frozen as of 19th May 2023.
The new ECHA CHEM database has been released by ECHA, and it now contains all REACH registration data. There are more details on the transition of ECHA's published data to ECHA CHEM here.
Diss Factsheets
Use of this information is subject to copyright laws and may require the permission of the owner of the information, as described in the ECHA Legal Notice.
EC number: - | CAS number: -
- Life Cycle description
- Uses advised against
- Endpoint summary
- Appearance / physical state / colour
- Melting point / freezing point
- Boiling point
- Density
- Particle size distribution (Granulometry)
- Vapour pressure
- Partition coefficient
- Water solubility
- Solubility in organic solvents / fat solubility
- Surface tension
- Flash point
- Auto flammability
- Flammability
- Explosiveness
- Oxidising properties
- Oxidation reduction potential
- Stability in organic solvents and identity of relevant degradation products
- Storage stability and reactivity towards container material
- Stability: thermal, sunlight, metals
- pH
- Dissociation constant
- Viscosity
- Additional physico-chemical information
- Additional physico-chemical properties of nanomaterials
- Nanomaterial agglomeration / aggregation
- Nanomaterial crystalline phase
- Nanomaterial crystallite and grain size
- Nanomaterial aspect ratio / shape
- Nanomaterial specific surface area
- Nanomaterial Zeta potential
- Nanomaterial surface chemistry
- Nanomaterial dustiness
- Nanomaterial porosity
- Nanomaterial pour density
- Nanomaterial photocatalytic activity
- Nanomaterial radical formation potential
- Nanomaterial catalytic activity
- Endpoint summary
- Stability
- Biodegradation
- Bioaccumulation
- Transport and distribution
- Environmental data
- Additional information on environmental fate and behaviour
- Ecotoxicological Summary
- Aquatic toxicity
- Endpoint summary
- Short-term toxicity to fish
- Long-term toxicity to fish
- Short-term toxicity to aquatic invertebrates
- Long-term toxicity to aquatic invertebrates
- Toxicity to aquatic algae and cyanobacteria
- Toxicity to aquatic plants other than algae
- Toxicity to microorganisms
- Endocrine disrupter testing in aquatic vertebrates – in vivo
- Toxicity to other aquatic organisms
- Sediment toxicity
- Terrestrial toxicity
- Biological effects monitoring
- Biotransformation and kinetics
- Additional ecotoxological information
- Toxicological Summary
- Toxicokinetics, metabolism and distribution
- Acute Toxicity
- Irritation / corrosion
- Sensitisation
- Repeated dose toxicity
- Genetic toxicity
- Carcinogenicity
- Toxicity to reproduction
- Specific investigations
- Exposure related observations in humans
- Toxic effects on livestock and pets
- Additional toxicological data
Eye irritation
Administrative data
- Endpoint:
- eye irritation: in vitro / ex vivo
- Type of information:
- experimental study
- Adequacy of study:
- key study
- Study period:
- From 01 April to 27 June 2022
- Reliability:
- 1 (reliable without restriction)
- Rationale for reliability incl. deficiencies:
- guideline study
- Remarks:
- conducted under GLP conditions
Data source
Reference
- Reference Type:
- study report
- Title:
- Unnamed
- Year:
- 2 022
- Report date:
- 2022
Materials and methods
Test guideline
- Qualifier:
- according to guideline
- Guideline:
- OECD Guideline 492 (Reconstructed Human Cornea-like Epithelium (RhCE) Test Method for Identifying Chemicals Not Requiring Classification and Labelling for Eye Irritation or Serious Eye Damage)
- Version / remarks:
- 18 June 2019
- Deviations:
- no
- GLP compliance:
- yes (incl. QA statement)
Test material
- Reference substance name:
- 3,7-dimethylnon-6-en-1-ol
- Cas Number:
- 41972-59-2
- Molecular formula:
- C11H22O
- IUPAC Name:
- 3,7-dimethylnon-6-en-1-ol
- Test material form:
- liquid
Constituent 1
Test animals / tissue source
- Species:
- human
- Details on test animals or tissues and environmental conditions:
- The EpiOcular™ human cell construct, provided by the MatTek Corporation, will be used in this study. The use of EpiOcular"' cultures offers features appropriate for a model for ocular irritation. First, the model is composed of stratified human keratinocytes in a three-dimensional structure.
Secondly, test materials can be applied topically to the model so that water insoluble materials may be tested. Prior to use, each plate (6-, 12-, and 24-well) and its cover will be uniquely identified in permanent marker with a plate number, the test article number, and the test phase.
Test system
- Vehicle:
- unchanged (no vehicle)
- Controls:
- yes, concurrent positive control
- yes, concurrent negative control
- Amount / concentration applied:
- TEST MATERIAL
- Amount(s) applied: 50 µL
- Concentration: Undiluted - Duration of treatment / exposure:
- 30±2 minutes
- Duration of post- treatment incubation (in vitro):
- - Post-treatment immersion period: 12±2 minutes
- Post-treatment incubation period: 120±15 minutes - Number of animals or in vitro replicates:
- Each test article and control were tested by treating at least 2 tissues.
- Details on study design:
- Assessment of Direct Test Article Reduction of MTT:
Prior to conducting any assays with viable tissues, it is necessary to assess the ability of each test article to directly reduce MTT. A 1.0 mg/ml MTT solution will be prepared.
Approximately 50 μl (liquid test articles) or approximately 50 mg (using dosing spoon or pre-weighed) (solid test articles) will be added to 1.0 ml of the MTT solution and the mixture incubated in the dark at 37 ± 1 °C in a humidified atmosphere of 5 ± 1% CO2 in air (standard culture conditions) for 180 ± 10 minutes. A negative control (SO μL of sterile deionized water) will be run concurrently. If the MTT solution color turns blue/purple, the test article is presumed to have reduced the MTT. Water insoluble test materials may show direct reduction (darkening) only at the interface between the test article and the medium.
In cases where the test article is shown to reduce MTT, a functional check using freeze killed tissues is performed in at least l definitive assay to evaluate whether the test material is binding to the tissue and leading to a false MTT reduction signal.
Assessment of Colored or Staining Materials:
Prior to conducting any assays with viable tissues, it is necessary to assess if the test articles interfere with the photometric MTT measurement. Each test article should be checked for its colorant properties. Approximately 50 μl (liquid test articles) or approximately 50 mg (using one leveled dosing spoon or pre-weighed) (solid test articles) will be added to 2.0 ml isopropanol in 6-well plates and placed on an orbital plate shaker for two to three hours at room temperature. Two x 200 μL aliquots of the isopropanol solutions and 2 blank samples of isopropanol are transferred to a 96-well plate, and the absorbance is measured with a plate reader, with the "shake" function selected, at the MTT measurement wavelength .
Some test articles may precipitate or become cloudy after addition to the isopropanol and interfere with the optical density (OD) measurement. In such cases, after the two to three hour shaking period, the test article-isopropanol mixture may be transferred into centrifuge tubes and centrifuged (in a centrifuge with settings up to 15,000 rpm, for up to S minutes at room temperature) prior to transfer to the 96-well plates for the absorbance measurement. The same centrifugation procedure may be performed after the isopropanol extraction period in the definitive assay.
If, after subtraction of the OD for the blank isopropanol, the OD of the test article solution is > 0.08 the material has to be considered as possibly interfering with the MTT measurement.
pH Determination:
The pH of each liquid test article (and/or dosing dilution as appropriate) will be determined, if possible. The pH will be determined using pH paper (e.g., with a pH range of O to 14 to estimate, and/or a narrower pH range). The typical pH increments on the narrower range pH paper are approximately 0. 3 to 0.5 pH units. The maximum increment on the pH paper is 1.0 pH units.
Receipt of the EpiOcular model:
Upon receipt of the EpiOcular assay materials, the solutions will be stored as indicated by the manufacturer. The tissue will be stored at 2 to 8 °C until used. On the day of receipt, an appropriate volume of EpiOcular™ Assay Medium will be warmed to approximately 37 °C. One (1.0) milliliter of Assay Medium will be aliquoted into the appropriate wells of labelled 6-well plates. The 6-well plates will be labelled with the test article or control codes and exposure times. Each tissue will be inspected for air bubbles between the agarose gel and cell culture insert prior to opening the sealed
package. Cultures with air bubbles greater than 50% of the cell culture insert area will not be used . Each 24-well shipping container will be removed from its plastic bag and its surface disinfected by wiping with 70% ethanol-soaked tissue paper. The tissues will be allowed to come to room temperature for at least 15 minutes prior to transfer to the 6-well plates . An appropriate number of tissues will be transferred aseptically from the 24-well shipping containers into the 6-well plates. The EpiOcular tissues will be incubated at standard culture conditions for 60 ± 5 minutes. After the incubation, the tissues will either be refed, or transferred to new plates containing fresh warmed media and incubated at standard culture conditions overnight (16 to 24 hours) . Upon opening the bag, any unused tissues remaining on the shipping agar at the time of tissue transfer will be briefly gassed with an atmosphere of 5% CO2/95% air, and the bag will be sealed and stored at 2 to 8 °C for subsequent use.
Definitive Assay-Treatment of Liquid Test Articles:
Each test article and control will be tested by treating at least 2 tissues.
An appropriate volume of EpiOcular™ Assay Medium will be warmed to room temperature for conducting the post-soak immersion incubation in 12-well plates and the post-treatment incubation in 6-well plates. After the overnight incubation, the tissues will be pre-treated with 20 μl of sterile Ca++ Mg++ Free-DPBS (CMF-DPBS). If the sterile CMF·DPBS does not spread across the tissues, the plate may be tapped to assure that the entire tissue surface is wetted. The tissues will be incubated at standard culture conditions for 30 ± 2 minutes.
After the 30 ± 2-minute sterile CMF-DPBS pre-treatment, each liquid test and control article will be tested by applying SO μL topically on the EpiOcular™ tissues. The tissues will be incubated at standard culture conditions for 30 ± 2 minutes. At the end of the 30 ± 2-minute treatment time, the test articles will be removed by extensively rinsing the tissues with sterile CMF-DPBS brought to room temperature, as described in detail below. If a dosing device is used, it will be removed and discarded.
Three clean beakers (glass or plastic with 100 ml capacity), containing ~100 ml each of sterile CMF-DPBS will be used per test article (8 oz/220 ml disposable specimen containers from Falcon, Cat# 354020 are suggested). Each test article utilizes a different set of 3 beakers. The cell culture insert containing the tissue will be lifted out of the medium by grasping the upper edge of the plastic "collar" with fine forceps. Use of curved forceps facilitates handling and decanting. To assure throughput, the tissues may be rinsed 2 at a time.
At the end of the exposure period, the test or control articles will be decanted from the tissue surface onto a clean absorbent material (paper towel, gauze, etc.) and the cultures dipped into the first beaker of sterile CMF-DPBS, swirled in a circular motion in the liquid for approximately two seconds, lifted out so that the cell culture inserts are mostly filled with sterile CMF-DPBS, and the liquid will be decanted back into the container. This process will be performed two additional times in the first beaker. The culture will then be rinsed in the second and third beakers of sterile CMF-DPBS 3 times each in the same fashion. Finally, any remaining liquid will be decanted onto the absorbent material. Decanting is most efficiently performed by rotating the cell culture insert to approximately a 45· angle (open end down) and touching the upper lip to the absorbent material (to break the surface tension).
After rinsing, the tissue will be immediately transferred to and immersed in 5 ml of previously-warmed Assay Medium in a labelled 12-well plate for a 12 +/- 2 minute immersion incubation (Post-Soak) at room temperature. This incubation in Assay Medium is intended to remove any test article absorbed into the tissue.
At the end of the Post-Soak immersion, each cell culture insert will be removed from the Assay Medium, the medium will be decanted off the tissue, the insert will be blotted on absorbent material, and transferred to the appropriate well of the labelled 6-well plate containing 1 ml of warm Assay Medium. The tissues will be incubated for 120 :I: 15 minutes at Standard Culture Conditions (Post-treatment Incubation).
MTT Assay:
A 1.0 mg/ml MTT solution will be prepared. Three hundred microliters of the MTT solution will be added to each designated well of a labelled 24-well plate. At the end of the Post-treatment Incubation, each cell culture insert will be removed from the 6-well plate and gently blotted on absorbent material. The tissues will be placed into the 24-well plate containing 0 .3 ml of MTT solution. The t issues will be incubated in the MTT solution for 180 ± 10 minutes at Standard Culture Conditions .
After 180 ± 10 minutes, each cell culture insert will be removed from the plate, the bottom of the insert blotted on absorbent material, and then transferred to a labelled 24-well plate containing 2.0 ml of isopropanol in each designated well. The plates will be sealed with parafilm (between the plate cover and upper edge of the wells) or using a standard plate sealer, and are either stored overnight at 2 to 8 °C in the dark or immediately extracted. To extract the MTT, the plates are placed on an orbital plate shaker and shaken for 2 to 3 hours at room temperature.
At the end of the extraction period, the liquid within each cell culture insert will be decanted into the well from which it was taken. The extract solution will be mixed and two x 200 μL aliquots will be transferred to the appropriate wells of a labelled 96-well plate(s). Two hundred microliters of isopropanol will be added to the wells designated as blanks. The absorbance at 550 nm (ODsso) (a range of 540 to 570 nm is acceptable but should be consistent within a laboratory's data set) of each well was measured with a Molecular Devices VersaMax plate reader with the "shake" function selected.
Killed Controls for Assessment of Residual Test Article Reduction of MTT:
In cases where the test article is shown to reduce MTT, only test articles that remain bound to the tissue after rinsing, resulting in a false MTT reduction signal, present a problem. To demonstrate that residual test article is not acting to directly reduce the MTT, a functional check is performed in the definitive assay to show if the test material is not binding to the tissue and leading to a false MTT reduction signal.
To determine whether residual test article is acting to directly reduce the MTT, at least one freeze-killed control tissue per test article is used. Freeze-killed tissue is prepared by placing untreated EpiOcular"' constructs in the -20 •c freezer at least overnight, thawing to room temperature, and then refreezing. Once frozen, the tissue may be stored indefinitely in the freezer. Freeze-killed tissues may be received already prepared from MatTek Corporation. To test for residual test article reduction, at least 1 killed tissue will be treated with the test article in the normal fashion . All assay procedures will be performed as for the viable tissue. A killed control treated with sterile deionized water (negative killed control) will be tested in parallel since a small amount of MTT reduction
is expected from the residual NADH and associated enzymes within the killed tissue. Additional steps must be taken to account for the chemical reduction or the test article may be considered untestable in this system.
Colorant Controls (CC) for Assessment of MTT Interaction:
In cases where a colored test article is shown to interact with the MTT measurement, colorant controls should be run alongside the live tissues. Ideally, colorant control tissues will be tested concurrently in the Definitive Assay; however, in some cases, follow-up testing of colorant controls may be warranted. To determine whether the test article is interfering with the MTT measurement, at least 1 live colorant control tissue per test article is used. The colorant control tissues are treated in the same way as the liquid or solid protocols, with the exception that in contrast to the normal viability test, no MTT assay is performed. The tissues are incubated in standard assay medium instead of MTT for the 180 ± 10-mlnute incubation.
Colorant Control-Killed Control experiment:
In the event that both a killed control experiment and a colorant control experiment are needed, an additional set of controls will be required to avoid a possible double correction for color interference. At least 1 killed control tissue will be treated with the test article using the same procedures as described for the colorant controls for assessment of MTT interaction. The ODsso values from the colorant controls will be analyzed as described below.
Presentation of Data:
The raw absorbance values will be captured, and the following calculations made:
The mean OD550 value of the blank control wells will be calculated. The corrected OD550 values of the negative control will be determined by subtracting the mean OD550 of the blank control from the negative control raw OD550 values. The mean corrected OD550 value of the negative control will be determined. The corrected OD550 values of the individual test article OD550 values and the positive control OD550 values are determined by subtracting the mean OD550 of the blank control from their raw OD550S. Generally, all calculations will be performed using Microsoft Excel. Although the algorithms discussed are performed to calculate the final endpoint analysis at the treatment group level, the same calculations can be applied to the individual replicates .
Corrected Test Article 0D550 = Test Article 0D550 - Blank Mean 0D550
If killed controls (KC) are used, the following additional calculations will be performed to correct for the amount of MTT reduced directly by test article residues. The OD550 value
for the negative control killed control will be subtracted from the OD550 values for each of the test article-treated killed controls, to determine the net OD550 values of the test article-treated killed controls.
Net 0D550 for each test article KC = Mean Raw 0D550 Test Article KC - Mean Raw 0D550 Negative Control KC
The net OD550 value represents the amount of reduced MTT due to direct reduction by the test article residues. The net OD550 value will be subtracted from the corrected OD550 values of the viable test article-treated EpiOcular™ tissues, to obtain final corrected OD550 values . If the net OD550 results in a negative value, a correction for the viable tissue OD550 will not be required.
Final Corrected 0D550 = Corrected Test Article ODno (viable) - Net 0D550 Test Article (KC)
If the direct reduction of MTT by the test article is greater than 30% of the negative control, the test article may be considered untestable with MTT.
The following% of Control calculations will be made:
% of control = ((Corrected OD550 of each Test Article or Positive Control Exposure Time)/(Corrected Mean 0D550 of Negative Control))*100
If colorant controls (CC) are used, the following additional calculation will be performed to correct for the amount of interference by the colored test material. The OD550 value for the colorant control will be subtracted from the corrected OD550 value for the viable tissues.
Corrected 0D550 of the Test Article= Corrected Test Article 0D550 (viable) - CC 0D550
If colorant control-killed controls (CC-KC) are used, the OD550 value of the CC-KC will be added to corrected OD550 values of the viable treated tissues to obtain a final corrected OD550 value.
Final Corrected ODsso of the Test Article = Corrected Test Article 0D550 (viable) - Net KC 0D5550 - CC 0D550 + CC - KC 0D550
The following calculation will then be performed:
% of Viability = ((Mean Final Corrected 0D550 of Test Article or Control Tissue)/(Corrected Mean 0D550 of Negative Control)) x 100
CRITERIA FOR DETERMINATION OF A VALID TEST:
The assay will be accepted if the mean negative control OD550 > 0.8 and < 2.5, and the mean relative viability of the positive control is <= 50%.
EVALUATION OF TEST RESULTS:
The following Prediction Model has been endorsed by the European Centre for the Validation of Alternative Methods (ECVAM) Scientific Advisory Committee (ESAC) for the prediction of ocular
irritation. A test article is predicted to not require classification or labelling for ocular irritation (GHS No Category) if the mean relative viability of the treated tissues is greater than 60% of the
mean viability of the negative control. A test article is predicted to potentially require classification and labelling according to UN GHS {Category 1 or 2) if the mean relative viability of the treated tissues is <= 60% of the mean viability of the negative control.
mean tissue viability <=60% -> GHS Category 1 or 2*
mean tissue viability > 60% -> No GHS Category
*Additional testing would be required to discriminate between a category 1 or 2 classification.
Results and discussion
In vitro
Results
- Irritation parameter:
- mean percent tissue viability
- Run / experiment:
- Main test
- Value:
- 64.03
- Vehicle controls validity:
- not applicable
- Negative controls validity:
- valid
- Positive controls validity:
- valid
- Remarks on result:
- no indication of irritation
- Other effects / acceptance of results:
- Acceptability criteria:
The assay results were accepted when the corrected mean OD550 value for the negative control exposure time (1.828) was > 0.8 and < 2.5 and the mean relative viability of the positive control was ≤ 50%.
Applicant's summary and conclusion
- Interpretation of results:
- GHS criteria not met
- Conclusions:
- The test article resulted in a viability of 64.03% relative to the negative control. According to the
prediction model presented in OECD 492, the test article is predicted to not require classification or
labelling for ocular irritation (GHS No Category). - Executive summary:
An in vitro eye irritation test using the Reconstructed human Cornea-like Epithelium (RhCE) (EpiOcular™ tissue) model was performed according to the OECD Guideline 492 and in compliance with GLP to predict the acute eye irritation potential of the test substance.
The test article resulted in a viability of 64.03% relative to the negative control. According to the prediction model presented in OECD 492, the test article is predicted to not require classification or labelling for ocular irritation (GHS No Category).
Information on Registered Substances comes from registration dossiers which have been assigned a registration number. The assignment of a registration number does however not guarantee that the information in the dossier is correct or that the dossier is compliant with Regulation (EC) No 1907/2006 (the REACH Regulation). This information has not been reviewed or verified by the Agency or any other authority. The content is subject to change without prior notice.
Reproduction or further distribution of this information may be subject to copyright protection. Use of the information without obtaining the permission from the owner(s) of the respective information might violate the rights of the owner.